This works great for me. I didn’t want anything mounted permanently inside. I first ran the piping through the tent but it lost to much heat. Now it will get me up to 60° when its in the single digits. Game changer.
9 Likes
@bipNdip as Phil mentioned I’ve tried a few solutions. What I would say is don’t waste your money on lithium heated battery. I heard back from Renogy and the operating temperature doesn’t go down below -20c.
So really, I’ve found I get the same performance out of a Gel and lithium. I’m going to end up having to re-design my electrical with a ‘quick’ connect method. This way I can remove the battery and store it at room temperature when it’s not in use. Which is 5 days a week, the rig usually goes out every weekend.
So I would recommend something like that unless you’re able to park your rig in a heated garage. Batteries don’t like the cold, period.
Since my battery powers more than just the heater having a contained battery heater unit wouldn’t work for me. But my heater is external in a case as I use it in my work truck as well with a portable deep cycle.
Hope that helps.
They actually also turn on the glow plugs when it’s turned off. This is to burn off any carbon and is usually around 9amps. People should also note, that the heater draws more amperage based on temp setting. So if you have it cranked it’s going to draw way more current.
4 Likes
On mine (cheap knock off) the difference from low to high is minimal. It seems to range from around .5 AH on low to 2 AH on high.
I have noticed the same. its really about fuel consumption on high…the power is just to run the fan and fuel pump and those really don’t need much.
Also if you are at higher elevations don’t forget to change your fuel consumption rate or they flood out - that seems to be the biggest issue people have that causes failures.
Very true. Like a Diesel engine on a vehicle.
I use a Planar suitcase heater with an AGM battery housed in a Home Depot homer tool box and keep it in the tent so it stays warm. We did a a couple days in Lake Curicanti with sub zero temps and we were toasty.
1 Like
What mount did you use to protect the bed composite from the exhaust pipe? And did you attach the exhaust silencer or does it just dangle down? I’m interested in doing something similar
I used one of these for the passthrough VTurboWay Stainless Steel 316… https://www.amazon.com/dp/B09H2RY6BT?ref=ppx_pop_mob_ap_share
And one of these with a short bit of metal pipe to create a pressure fit connection between the heater and the port SUPERFASTRACING Exhaust Pipe… Amazon.com haven’t had any issues I would suggest putting 2 of these sets in so you have fresh air coming in through one.
I added this to pull fresh air from outside as an afterthought SHENGHUISS 2"(50mm) Boat Gas Deck… Amazon.com wish I had done 2 of the exhaust at the same time.
I did route the exhaust and attach it with the silencer there is a pic up above of what I did
1 Like
Thanks, appreciate the information. Any regrets placing the holes in the bed vs teh wheel well as I have see on some other installs?
Nope not at all, Sometimes wish I had mounted things the other direction parallel with the end of the bed but really that’s the only thing
Ok, bumping this up as it’s almost that time of year (I hope! Smoky as hell out there now).
Running a GFC on a Tundra and have a chinese diesel heater I started using last year. Currently built into a big rubbermade box with the hot air being ducted into a partially opened GFC side panel. It works but it’s not a real clean setup. I want to be able to use this for hunting season and powder chasing in the winter.
-
Are there any type of molle boards that can attached to the side of a GFC using the T-slots or otherwise? Several posts above is a mantis type camper with the heater mounted outside. I think that would be an ideal setup for me. Keep it neat and tidy. I could run power and heat into the truck bed area and remove one panel so heat flows up into the tent. I have done it this way in the past and kept it 60*+ all night during single digits outside. Heating the truck bed area allows for drying clothes etc.
-
What size pelican style boxes are you guys using for this heater?
- Crazy to cut a 3" hole in one of the GFC panels with a blast gate installed to close off when not using the heater?
I used a harbor freight apache case, 3800.
Ok good to know. I actually have one of those I was going to use as a bike tool box, and just assumed it wasn’t large enough for the heater.
I use one of these tables that attach to the rear tire of my truck. It’s perfectly situated to duct the heat into the camper.
Summer time use includes using the table as an extension of my food prep area.
I highly recommend this product!
3 Likes
Ok that’s pretty sweet and may work perfectly. Thanks.
I still need to plumb and hook mine up in the camper but I finally set it all up and tested it out today.
On full draw maybe 36w, on low setting 6w.
Holy moly that heater cooks!!
3 Likes
Make sure you do the elevation adjustments on it or you will have fouling issues.
@ScottH how do you do that? Instructions are awful…
I do think one of the screen shows altitude in meters.
It really depends on what control unit you have- there are many. once you figure that out find the youtube for your controller and go from there.